CHAPTER 9 Observe Urgent down within the change shaft crank really helps to align the change pawl Using the shift drum pins.
PalmsÂCost-free Fob: Sensible Protection Technique Using with a Fob Generally have the fob when Using, loading, fueling, relocating, parking or servicing the motorcycle. Carry the fob in a convenient pocket. Do not leave the fob hooked up to the handlebars or retail outlet the fob in a saddlebag or Tour ® . Unintentionally leaving the fob with the motorbike when It truly is parked stops the system from activating the alarm. Do not trip with the fob saved in a steel scenario or with the fob closer than 3.0 in. 76 mm to a cell phone, PDA, display or other Digital machine.
The engine off/operate change must be utilized to shut the motor off. one. To shut the engine off, drive the top of the off/operate change to the ignition OFF placement. 2. See Ignition Swap: VRSC Styles. Switch the ignition crucial to the OFF place to transform the ignition electric power fully OFF. Throttle Handle Grip See Handlebar Controls: VRSC Products. The throttle Command grip (nine) is located on the ideal handlebar Command and is operated with the ideal hand. To lower rider exhaustion on very long excursions, a spring loaded throttle friction adjustment screw (10) is located at the bottom of the throttle grip clamp on nonÂcruise Geared up products. one. Slowly and gradually switch throttle Handle grip clockwise (toward the front of the bicycle) to near the throttle (decelerate). 2. Little by little flip throttle control grip counterclockwise (towards rear of bicycle) to open the throttle (accelerate). Do not tighten throttle friction adjustment screw to The purpose wherever the engine will not return to idle immediately.
A bend could cause a stud failure later on all through engine oper- ation. 10. Take away the pistons and rings as explained in this chap- Lower absent part ter.
The boot's sole, insole and higher are bound using resoleable Goodyear? Welt design processes, adding yrs of use with appropriate treatment
Right before setting up spark plugs, the hole should really be checked and altered if needed to 0.035 in. (0.89 mm). Be certain your motorbike has the appropriate spark plug. Use a 10R12A spark plug. Spark plugs ought to be tightened to the torque specified for good warmth transfer. Tighten spark plugs to seventeen ftÂlbs (23 Nm) per spark plug. NOTES: If a torque wrench is not accessible, tighten the spark plugs finger tight; then tighten an extra a single quarter change with a spark plug wrench. The VRSC is Geared up with plugÂtop coils. To inspect the spark plugs, the coils should be removed. Seek the advice of the VRSC Service Manual for the good company procedure. Shock Absorbers Refer to Frequent Service Intervals: 2009 VRSC Products. Inspect shock absorbers and rubber bushings for leaks and bushing deterioration at suitable intervals. Ignition The engine in your bike has been intended specially to accomplish optimum gasoline overall economy inside exhaust emission controls.
Tricky Candy Custom components contain “massive flake†paint finishes, 3 of that can be selectively presented to be a check here strong-colour solution on 5 Harley-Davidson generation bikes for 2013.
Procedure of the motorbike could result in Demise or critical damage. (00043a) Some features spelled out are special to particular styles. These characteristics might be available as components for your HarleyÂDavidson motorcycle. See a HarleyÂDavidson dealer for a finish list of extras that will in shape your particular bike. Ignition Switch: VRSC Types The automaticÂon headlamp element offers amplified visibility of the rider to other motorists. Be confident headlamp is on at all times. Lousy visibility of rider to other motorists can outcome in Demise or severe harm. (00030b) See the YOUR OWNER'S Handbook segment at the commencing of this manual. Be absolutely sure to document all of your key figures in the House presented at the entrance of this guide. The ignition change controls electrical functions of the motorbike.
 Failure to absolutely disengage the clutch can end in devices problems. (00182a) The change sample is 1st gear down, subsequent four gears up. NOTE: Always start motor with transmission in neutral. Generally start out motorbike forward motion in initial gear. one. With bike motor working and jiffy stand retracted, pull the clutch hand lever in towards handlebar grip to fully disengage clutch.
CHAPTER 3 vent the aspect plates and rollers from rusting. The actual chain lubrication is enclosed throughout the chain via the O-rings. two. Journey the motorbike several miles to warm the drive chain. A heat chain boosts lubricant penetration. three.
The locking compound over the outdated bolts can't be reused; if mounted, the aged bolts may possibly loosen for the duration of engine operation. 4. Put in the alternator stator as explained in Chapter Twelve.
“There isn’t seriously a cruiser that we haven’t improved in a way by means of style, electric power, or accessibility.†Right here’s a look at some of the new 2016 Harley-Davidson bikes.
CHAPTER TWO the established-alter knob until finally the meter needle reads zero. When the sales opportunities are uncrossed, the needle must move to one other Male stop of the size, indicating infinite resistance.
Drain gasoline remaining during the tank after valve removal. Cleaning and Inspection 1. Inspect the filter mounted along with the gasoline valve. Re- shift contamination within the filter.